Alubrite
Part No. RXSOL-39-2697-005
Alubrite Condensor Coil Cleaner
This is specially formulated for use as a coil cleaner and filter adhesive for cooling coils of the air- conditioning systems.
Key details
| Part number | RXSOL-39-2697-005 |
|---|---|
| Generic name | Alubrite Condensor Coil Cleaner |
| Available pack sizes | 5 Ltrs, 10 Ltrs, 20 Ltrs. 25 Ltrs. |
| Supply locations | Active SK COIL Cleaner PINK manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai UAE, Muscat Oman, Kenya Africa. Get the best quality of Active SK COIL Cleaner PINK at a competitive price from us. We have ready stock of Active SK COIL Cleaner PINK in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders. |
| Usage unit | Ltr. |
| Quantity per unit | 5.00 |
Need this product at your port or plant?
Enquire NowRXSOL-16-2697-005 is a concentrated outdoor condenser coil cleaner and brightener. It effectively foams away stubborn,"baked on" lint, smoke film, insects, feathers, grass, leaves and other deposits from air cooledcondenser coils. The expanding foam pushes contamination out of the coil and is easily rinsed away with water. In addition to removing contaminants, the RXSOL Active SK COIL Cleaner PINK formula effectively restores efficiency and reduces operating cost by removing hidden oxidation from the coil surfaces.
RXSOL-16-2697-005 is a special formulation of solvents and acids specifically blended for use in cleaning and brightening outdoor aluminum finned air cooled condenser coils.
Produced and packaged in our ISO 9001 registered facility.
USES:
Deep cleaning of outdoor condenser coils to restore efficiency and increase performance of the system.
DILUTION RATIOS:
Because RXSOL-16-2697-005 is highly concentrated, it must be diluted prior to use. Dilution also improves penetration into the coil and increases product performance. Actual dilution ratios will vary according to the application. The following is intended as a general
guideline:
- Up to 8-10 parts water to 1 part RXSOL Active SK COIL Cleaner PINK for light cleaning and brightening, when expanding foam is not required.
- 3-5 parts water to 1 part RXSOL Active SK COIL Cleaner PINK for foaming action on difficult cleaning tasks.
- 1-2 parts water to 1 part RXSOL Active SK COIL Cleaner PINK for use as a high foaming,aluminum finned, air cooled condenser coil cleaner.Use the minimum concentration required to accomplish your task.
Note: Do not use RXSOL-16-1697-003 at concentrations greater than 1:1 (less than 1 part water to 1 part RXSOL-16-2697-005 . Rinse the treated surfaces as well as the surrounding area thoroughly after use.
APPLICATION METHODS:
Low pressure, acid resistant tank sprayers are recommended.
Regardless of application method, avoid inhalation of mist or contact of liquid or mist with skin.
SUGGESTED INSTRUCTIONS FOR USE:
-
When handling RXSOL-16-2697-005 or any other strong chemical, be sure to wear chemical imperviousgloves,apron and splash goggles.
-
Determine required dilution ratio for the specific application. It is recommended to start with a dilution ratio of 10:1 and increase concentration until the desired results are achieved.
-
As with mixing all acids, place the desired amount of water into the tank and then add RXSOL-16-2697-005
-
Turn off fans and allow hot coils to cool before applying.
-
Using plain water, wet both the condenser coil as well as the area surrounding the equipment. Wetting the coil with water aids in product penetration and performance.
- Apply the properly diluted product to the coil surface. Whenever possible, apply solution from the outlet side of the coil. Allow product to remain on surface, normally 5-10 minutes. Do not allow product to dry on the coil. Note: In extreme cases, application may have to be repeated to achieve desired results.
-
If foaming does not occur, check for extreme grease buildup which will slow cleaning process. Foaming may not occur if coil is coated or painted.
- Rinse coils, tools and surrounding area thoroughly after completing the coil cleaning process
CHARACTERISTICS:
Heavy foaming action.
Solvent-Acid blend (pH: 2.0).
Removes oxidation - brightens aluminum.
Bright pink liquid.
CAUTIONARY NOTES:
This product is for professional use only.At full strength:
• It will cause burns to skin and eyes.
• Ingestion will cause severe and potentially fatal gastric distress.
• Vapors are harmful and may cause respiratory tract irritation.
• May be harmful to plants.
Refer to MSD sheet for further information. MSD sheets are available at your local wholesaler
.PACKAGE SIZES AVAILABLE:
RXSOL-16-1697-003 is available in 1, 5 and 55 gallon containers
ALTERNATE PRODUCTS:
-
Concentrated Alkaline Coil Cleaner.
-
Multi-Purpose Alkaline Cleaner.
- Concentrated Evaporator Coil Cleaner
| Product Code | RXSOL-39-2697-005 |
| Product Name | Alubrite |
CHEMICAL Name ::: Mixture of Hydroflouric, phosphric acid less then 15% and Non Hazardous Ingredients more then 70%
Company Details: A subsidiary Division of RX MARINE INTERNATIONAL ( INDIA )
DUBI CHEM MARINE INTERNATIONAL
Plot No- 37 A, BLOCK - " L"
AL HAYL Industrial Area
PO BOX No - 9395
FUJAIRAH , UAE
Email ::: dubichem @ rxmarine.com
Proprietory Blend Of Surfactant non hazardous ingrident Bio degradable with hydrofloric and phosphoric acid to clean COIL of AC
| CAS Registry No. | OSHA PEL | ACGIH TLV | Other Limits | % (Optional) | |
| Hydrofluoric Acid | 7664-39-3 | 3 ppm as F | 3 ppm (C) as F | 6 ppm as F | 15 |
| Phosphoric Acid | 7664-38-2 | 1 mg/m3 | 1 mg/m3 | (STEL) 3 mg/m3 | 15 |
| Non Hazardous Ingredients |
Proprietory Blend of RICE BRAN derivative ::: 30 % WATER :::20 % LABSA Bio :::10% Alcohol ::: 10% Colour Pigments |
------------ | ----------- | -------------- |
70 |
| INHALATION: | Inhalation of vapor or mist is corrosive to respiratory tract. Symptoms include coughing, wheezing, laryngitis, shortness of breath, headache, nausea, and vomiting. |
| EYE CONTACT | Liquid , irritating to eyes. Immediate irritation followed by destruction of tissue |
| SKIN CONTACT | Use gloves. Dont directly on naked skin |
| INGESTION: | moderately toxic, causes nausea, vomiting, loss of consciousness |
| CHRONIC Effects | Damage to kidneys and liver .Changes in bones or joints |
| INHALATION: | Ensure the victim’s clothing or skin has not been contaminated by the acid before removing the victim to fresh air. If breathing has stopped, begin artificial respiration. Call ambulance immediately for assistance |
| EYE CONTACT: | Flush eyes with water for 15 minutes with copious cool flowing water. If only one eye is affected, be careful not to flush contaminated water into the other eye. Tilt the head in the direction of the affected eye while flushing. Take the victim to a medical facility immediately, and apply ice water compress during transport. |
| SKIN CONTACT: |
Move the victim immediately under an emergency shower or other water source and flush the affected area with large amounts of cool running water. Immediately washing off the acid is of primary importance. Remove all contaminated clothing while flushing with water. If there is a large area of exposure, arrange for emergency medical assistance while the victim is being rinsed with water.Immediately after flushing with water, begin massaging calcium gluconate gel into the burn site. Apply the gel every 15 minutes and massage until pain/redness resolves or until medical care is available. The first aider should wear gloves when applying the gel to prevent transfer of the acid. |
| INGESTION: | Do not induce vomiting. Rinse mouth out with water. Call an ambulance immediately for assistance |
| FLASHPOINT (TEST METHOD): | None |
| FLAMMABLE LIMITS: | |
| LOWER: | NA |
| UPPER: | NA |
| GENERAL HAZARD: | NA |
| FIRE FIGHTING INSTRUCTIONS: . | Approach fire from upwind side. Avoid breathing smoke, fumes, mist, or vapors on the downwind side.Firefighters wear protective clothing and self-contained breathing apparatus |
| EXTINGUISHING MEDIA: | Dry powder, carbon dioxide (CO2), water fog or spray |
| HAZARDOUS COMBUSTION PRODUCTS: . | Smoke, irritating vapors, toxic fumes of POx, and corrosive F fumes, CO, CO2 |
LAND SPILL: Emergency response coordinator must have mandated training. Eliminate all ignition sources.
SMALL SPILLS: Pick up with absorbent materials and place in non-leaking containers; seal tightly for proper disposal or reuse.
LARGE SPILLS: Evacuate the hazard area of unprotected personnel. Wear appropriate respirator and protective clothing. Shut off source of leak if safe to do so.
Dike and contain. Remove with vacuum trucks or pump to storage/salvage vessels.
WATER SPILL: Notify proper authorities.
Clean up leaks/spills immediately to prevent soil or water contamination.
HANDLING: Avoid contact with skin, eyes, and clothing. After handling this product, wash hands before eating, drinking or smoking. If contact occurs, remove contaminated clothing. If needed, take first aid action shown in section IV. Launder contaminated clothing before reuse.
STORAGE: Store away from food stuffs, alkaline materials
PERSONAL PROTECTION: If TLV is exceeded wear NIOSH approved respirator. Use heavy rubber type gloves, full-face shield and boots, aprons, drench showers, eye wash as needed for protection against spills and/or splashes
| VAPOR PRESSURE: | ND |
| SPECIFIC GRAVITY (H2O=1): | 1.15 |
| SOLUBILITY IN WATER: | Complete |
| pH: | NA |
| BOILING POINT: | 212 F |
| APPEARANCE & ODOR: | Pink liquid, pungent odor |
| VAPOR DENSITY (Air=1): | >1 |
| EVAPORATION RATE (BuAc=1): | >1 |
| VOC: | 0% |
| FREEZING POINT: | ND |
| STABILITY: | Stable |
| CONDITIONS TO AVOID: | High temperatures |
| MATERIALS TO AVOID: | Alkaline materials may react with metals to produce gas. |
| HAZARDOUS DECOMPOSITION PRODUCTS: | Corrosive F fumes, toxic POx fumes, from combustion -smoke, CO, CO2 |
| HAZARDOUS POLYMERIZATION: | Will not occur |
Phospho LDLo: 220 mg/kg (unr - man)
LD50: 1230 mg/kg (oral - rat)
LD50: 2140 mg/kg (skin - rat)
NA
Dispose according to all local, state and federal regulations
| PROPER SHIPPING NAME: | Coil Cleaning Liquid |
| IDENTIFICATION NUMBER: | UN3264 |
| DOT Emergency Guide #: | 154 |
| Reportable Quantity (RQ): | Not applicable |
CERCLA (Comprehensive Environmental Response, Compensation and Liability Act): Reportable quantity is 100 pounds HF.Contact local authorities for other reporting requirements.
CALIFORNIA PROPOSITION 65: Not listed.
This information is furnished without warranty, expressed or implied, except that it is accurate to the our best knowledge . The data on this sheet related only to specific material designated here in. Rx Marine International assumes no legal responsibility for use or reliance upon these data.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
USES:
Deep cleaning of outdoor condenser coils to restore efficiency and increase performance of the system.
DILUTION RATIOS:
Because RXSOL-16-2697-005 is highly concentrated, it must be diluted prior to use. Dilution also improves penetration into the coil and increases product performance. Actual dilution ratios will vary according to the application. The following is intended as a general
guideline:
- Up to 8-10 parts water to 1 part RXSOL Active SK COIL Cleaner PINK for light cleaning and brightening, when expanding foam is not required.
- 3-5 parts water to 1 part RXSOL Active SK COIL Cleaner PINK for foaming action on difficult cleaning tasks.
- 1-2 parts water to 1 part RXSOL Active SK COIL Cleaner PINK for use as a high foaming,aluminum finned, air cooled condenser coil cleaner.Use the minimum concentration required to accomplish your task.
Note: Do not use RXSOL-16-1697-003 at concentrations greater than 1:1 (less than 1 part water to 1 part RXSOL-16-2697-005 . Rinse the treated surfaces as well as the surrounding area thoroughly after use.
APPLICATION METHODS:
Low pressure, acid resistant tank sprayers are recommended.
Regardless of application method, avoid inhalation of mist or contact of liquid or mist with skin.
SUGGESTED INSTRUCTIONS FOR USE:
-
When handling RXSOL-16-2697-005 or any other strong chemical, be sure to wear chemical imperviousgloves,apron and splash goggles.
-
Determine required dilution ratio for the specific application. It is recommended to start with a dilution ratio of 10:1 and increase concentration until the desired results are achieved.
-
As with mixing all acids, place the desired amount of water into the tank and then add RXSOL-16-2697-005
-
Turn off fans and allow hot coils to cool before applying.
-
Using plain water, wet both the condenser coil as well as the area surrounding the equipment. Wetting the coil with water aids in product penetration and performance.
- Apply the properly diluted product to the coil surface. Whenever possible, apply solution from the outlet side of the coil. Allow product to remain on surface, normally 5-10 minutes. Do not allow product to dry on the coil. Note: In extreme cases, application may have to be repeated to achieve desired results.
-
If foaming does not occur, check for extreme grease buildup which will slow cleaning process. Foaming may not occur if coil is coated or painted.
- Rinse coils, tools and surrounding area thoroughly after completing the coil cleaning process
Alubright
Need Alubrite for your operation?
Our team helps with product selection, dosage, safety data and delivery worldwide.
Request a Quote